Take Nuvoton NuMaker-IIoT-NUC980 running Linux as the platform and learn how to develop various functions. Watch this video, you will learn how to control GPIO to blink the LED on NuMaker-IIoT-NUC980 board. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/numaker-nuc980-iiot Contact us: SalesSupport@nuvoton.com

This video will introduce ARM TrustZone technology and show the example of how to program TrustZone on M2351. There is also a FIDO USB stick application demo in the end. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/m2351-series/ Contact us: SalesSupport@nuvoton.comon.com

Introduce the waterproof and noise immunity of ML56 touch key. Hello! Everyone! I am Nuvoton FAE Tim. Today, I will show you the waterproof and noise immunity of ML56 touch key. First introduce the waterproof and noise immunity of ML56 touch key. Good waterproof function, support finger touch with 2 mm depth water droplet. IEC 61000-4-6 conducted noise immunity (CNI) with 10 Vrms noise voltage. Next, we will explain the related parameter settings of the ML56 touch key, and first explain the touch sensitivity. #Pulse Width (Touch key sensing pulse width time control) Touch key sensitivity can be adjusted by setting Pulse Width properly, shorter Pulse Width setting comes with poor sensitivity and less power-consumption, vice versa. Then explain the stability of touch performance, Part 1. #Times (Touch key sensing times control) Touch key raw data stability can be adjusted by setting Times properly, shorter Times setting comes with poor raw data stability and less power-consumption, vice versa. Stability of touch performance, Part 2. #IIR (IIR filter) IIR filter can control the ratio of current raw data and previous one. User can enable IIR Filter to be against noise. It will increase the touch response time when enables IIR Filter. Stability of touch performance, Part 3. #Debounce (Touch key debounce) Touch key stability can be adjusted by setting Debounce properly, the debounce times for touch key entry (on) and release (off) detection, shorter Debounce setting comes with faster touch response time, vice versa. Stability of touch performance, Part 4. #Trace Baseline (Baseline is generated by “Calibration”) Touch key auto environment compensation is an algorithm that baseline tracking each touch key automatically at power-up and keeps compensating environment variation affects touch key performance during runtime. Based on the above parameter description, the following introduces the waterproof and noise immunity parameter settings. The first is waterproof parameter setting. Good waterproof function, support finger touch with 2 mm depth water droplet. Touch key system parameters are shown in the table Pulse Width = 500 ns Times = 128 Next is the noise immunity parameter setting IEC 61000-4-6 conducted noise immunity (CNI) with 10 Vrms noise voltage. Touch key system parameters are shown in the table. Pulse Width = 2 us Times = 128 IIR New = 6, Old = 2 Debounce Entry = 1, Release = 1 Then we use the ML56 NuMaker Board to show you the waterproof function of the touch key. Dip the finger in water first, and then touch the touch key. Repeat the above actions, we can see that the touch key still works normally and is not affected. Finally, we use the ML56 NuMaker Board to show you the noise immunity ability of the touch key. Turn on the walkie-talkie first, and then interfere with the touch key at close range, we can see that the touch key still operate normally and is not affected. That's all for today's video, thank you everyone! If you have any questions, please contact us. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Hello! Everyone! I am Nuvoton FAE Tim. Today, I will show you ML56 Capacitive Touch Key PCB Design. First introduce the Touch Sensor Channel Selection. Touch Sensor Channels. ML56 series supports up to 14 touch sensor channels. #Reference Sensor It is recommended to select one reference sensor at touch sensor channel TK7 or TK14. Maximize the distance between the reference sensor and other signals to minimize crosstalk. #Shield Electrodes Put the shield electrode around the touch sensor to get better signal quality and waterproof capability. Recommended to select shield channel at touch TK0, TK4 or clock out pins (P3.2 / P4.6 / P5.7). Next, we will explain the PCB Layout Rules. #Touch Key Shapes Recommended to have a 10 x 10 mm sensor area for good touch key sensitivity. Larger touch sensor electrode work better for thicker cover. #Reference Sensor Recommended to assign the reference key at touch channel TK7 or TK14. Maximize the distance to other signals to minimize crosstalk. Round shape electrode with 1 mm diameter size is enough for normal case. #Ground Plane It is recommended that the traces of the touch key have a good hatched ground plane surround. It is recommended to have hatched ground plane under the touch keys. Hatched ground plane with 6 mil trace and 50 mil grid. #Shield Electrode Put touch keys with shield electrode around which provides the same phase signal around touch keys. Hatched shield electrode with 6 mil trace and 50 mil grid. Shield electrode area needs to keep filled around the touch key in greater than 10 mm width. Finally, explain the Touch Key Cover Thickness. As the cover thickness increases, the touch key sensitivities will decrease. Larger touch key size work better for thicker cover. Recommended touch key diameter size with difference acrylic cover thickness as shown in the table. That's all for today's video, thank you everyone! If you have any questions, please contact us. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Hello! Everyone! I am Nuvoton FAE Tim. Today, I will show you ML56 Capacitive Touch Key Technology. First introduce the Capacitive Touch Key Fundamentals. The capacitance of the sensor without a finger touch is called as “parasitic capacitance”, CP. Parasitic capacitance results from the electric field between the sensor (including the sensor pad and traces) and other conductors in the system such as the ground planes, traces, any metal in the product’s chassis or enclosure, etc. The capacitance between the sensor pad and the finger is CF. The total capacitance CT of the sensor is the sum of CP and CF. Next, we will explain the ML56 Capacitive Touch Key Sensing Method. ML56 implements two switching capacitor banks for injecting charges to CP (or CT) and CR. CR is the parasitic capacitance of reference channel. After touch key calibration, CP and CR are balanced with CB and CCB (comparator output is “low”). Touch the sensing touch key which makes CT = CP + CF Now the negative input terminal voltage of the comparator is lower than positive side and comparator output is “high”. ML56 touch key controller will increase CCB to CCB’ to balance CT and CR again (comparator output is “low”). A finger touch can be detected by checking the difference of CCB and CCB’. By comparing the CCB’ shift level from CCB, the steady state to a predetermined threshold, the algorithm can determine whether the touch key is in ON (Touch) or OFF (No Touch) state. That's all for today's video, thank you everyone! If you have any questions, please contact us. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Nuvoton provides a development tool for capacitive Touch Sensors. The best feature of the calibration tool is that it uses the GUI to configure and tune your design automatically. Besides, the tool can export the configuration parameters and import them to another. Not only can greatly shorten the development time of developers, but also shorten the time for mass production. This video will introduce how to use this development tool and the definition of parameter. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Nuvoton announced the latest ML56 microcontroller, built-in capacitive touch sensing, LCD driver highly integrated low power platform. And provides capacitive touch sensor and LCD driver library. The solution is delivered through the API guide, which includes details on each function call, parameters and returns. Finally, this video provides an overview on how to develop a custom touch key and LCD application from the BSP release. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Take Nuvoton NuMaker-IIoT-NUC980 running Linux as the platform and learn how to develop various functions. Watch this video and you will learn how to install Buildroot for NuMaker-IIoT-NUC980 board before starting development. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/numaker-nuc980-iiot Contact us: SalesSupport@nuvoton.com #Training #Learning #Basic #en

Hello, everyone! I'm Chris, Field Application Engineer from Nuvoton Technology. Today, I will introduce you how to design NuMicro M251/ M252 application circuit. Let's start with the power application circuit of M251/M252. The external power should add 10uF and 0.1uF decoupling capacitors, and the capacitor should be placed close to the source of the external power supply. Before the external power enters the VDD/VDDIO/VBAT of the IC, 0.1uF bypass capacitors should be added separately, and the capacitors should be placed close to the IC. Before the external power enters the AVDD, the bead should be connected in series for filtering, and then 1uF, 0.1uF, and 0.01uF bypass capacitors should be added. The bead and capacitors should be placed close to the IC. Before connecting AVDD to VREF, first, connect the bead in series for filtering, and then add 2.2uF, 1uF, and 470pF bypass capacitors. The bead and capacitors should be placed close to the IC. A 1uF bypass capacitor should be added to the internal LDO power supply of the IC, and the capacitor should be placed close to the IC. AVSS and VSS should be connected in series with a bead for filtering. USB_VBUS should be connected in series with a 10-ohm resistor to enhance the ability of USB to resist EFT interference. USB_D+ and USB_D- should be connected in series with 27-ohm resistors for impedance matching. USB_VCC33_CAP needs to add a 1uF bypass capacitor. ICE_DAT and ICE_CLK should be connected to 100K ohm pull-up resistors. The two ends of the high-speed and low-speed crystal oscillators should be connected with an equivalent capacitance of 20pF to VSS. I2C_SCL and I2C_SDA should be connected to 4.7K ohm pull-up resistors. nRESET should be connected to a 10K ohm pull-up resistor and a 10 uF capacitor to VSS. The internal LDO power supply of the IC needs to add a 1 uF bypass capacitor, and the capacitor should be placed close to the IC. In addition, reference circuits for EBI, UART, SPI, and Audio are provided. VDD is connected to 4~32 MHz crystal oscillator, POR33, Power On Control, 5V to 1.5V LDO, IO Cell... and other circuits inside the IC. Among them, GPIO PF.4 to PF.6 and PA.0 to PA.5 output, the high level is equal to VDD. Vbus is connected to the USB 1.1 PHY inside the IC. This 1.5V regulator will provide 1.5V for Digital Logic, SRAM, Flash, POR15, LIRC, MIRC, HIRC... and so on. Vbat is connected to internal 1.5V RTC_LDO and provides 1.5V voltage for RTC, 32.768 kHz crystal oscillator, IO Cell PF.6. VDDIO is connected to some IO cell for use, and the output high level of PA.0 to PA.5 is equal to VDDIO. AVDD is connected to the analog circuit inside the IC, and VREF is the reference voltage of the analog circuit. That's all for the hardware design of the NuMicro M251/M252 series instruction. Thank you for watching it. If you have further questions, please contact us. #Tool #Training #Learning #Intermediate #en - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/numaker-m251sd Contact us: SalesSupport@nuvoton.com

Hello everyone, I am Chris, the field application engineer from Nuvoton Technology. Today I will introduce the power modes of the M251/M252 series microcontroller. The M251/M252 series has multiple power modes. The differentiation is based on power consumption, wake-up time, the operable CPU, and peripherals. In normal mode, the CPU is running normally. In Idle mode, only the CPU clock is disabled while other peripherals work as usual. Normal mode and idle mode can be divided into high-efficiency high-speed PL0 mode and low-power low-speed PL3 mode according to CPU operating speed. We should note that in the low-speed PL3 mode, only the clock source of the CPU and peripherals is 32.768 or 38.4 kHz can run. In power-down mode, there are three types according to power consumption. The first is NPD (Normal Power Down Mode). The CPU and high-speed peripherals stop running, and only the low-speed peripherals can work normally. The second is FWPD (Fast Wake Up Power Down Mode), which is the fastest wake-up of the three power-down modes but consumes more power. The third is DPD (Deep Power Down Mode), which consumes the lowest power among the three power-down modes, but the data in the RAM cannot be retained, and the wake-up speed is the slowest. Specific peripherals or pins can only activate the wake-up. For power consumption and wake-up time, we list the corresponding data. Users can choose the most suitable power mode according to the required power consumption and wake-up time. We need to note that FWPD mode will consume more power in the power-down mode because this mode wakes up the fastest. The DPD mode is the least power consumption, but the longest wake-up time.， Also, normal mode is a normal working mode, so there is no need to wake up. The time unit of the idle mode is different from the power-down mode, which is five cycles. The length of a cycle is determined according to the operating frequency used by the system. In the related resources section, we provide application notes for power management, which have more detailed operations and descriptions. If you want to know more, please download it from the URL in the video. There are also various power mode entry and wake-up methods in the BSP package; you can also refer to and use it. That’s all for the power modes introduction. Thank you for watching it. Please subscribe to our channel for more video resources. If you want to know more information, please contact us. #Tool #Training #Learning #Intermediate #en - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/numaker-m251sd Contact us: SalesSupport@nuvoton.com

Hello everyone I am Chris, the Field Application Engineer from Nuvoton Technology. Today I will introduce the programming and debugging tool, called NuLink-Gang, and NuLink2-Pro. And I will show you in what kind of situation you can utilize the tools. During system development, Nuvoton provides three IDE interfaces: KEIL, IAR, and NuEclipse for user to develop source code. When programming the Chip, Nuvoton provides ICP programming Tool in PC and the debugger Nu-Link2-Pro for users to perform debugging and programming function. User who uses all of the Nuvoton Nu-Maker boards series can develop through the Nu-Link2-Me debugger and programmer; it’s attached to the board. During the mass-production stage, there are 2 modes for programming the target chip. One is online programming and the other is offline programming. At first, in online programming mode, user can use ICP programming Tool and a Nu-Link2-Pro to program a target chip. Besides, if it needs to program several chips at one times, the Nu-Link Command Tool supports program multiple develop board by several Nu-Link2-Pro. Nu-Link2-Pro also supports drag-and-drop Flash programming. User can intuitively complete the programming action. Nu-Link2-Pro In offline programming mode, user can pre-store the programming file in SPI flash, USB flash drive, or SD card. When user wants to program the target chip, pressing the programming button on Nu-Link2-Pro to complete the programming action. If it needs a large number of ICs to be programming, it recommends using the Nu-Link-Gang programmer. Nu-Link-Gang programmer can perform offline programming on four different chips at a time, significantly increasing the programming efficiency. Besides, Nu-Link-Gang programmer can also use the control bus to connect with an automatic programming machine for automatic programming. In the system upgrade, Nu-Link2-Pro also provides five standard communication interfaces such as SPI, I2C, UART, RS485, and CAN for transmission, which is convenient for users to upgrade the system. That’s all for the introduction of Nuvoton’s programming and debugging tool, NuLink-Gang, and NuLink2-Pro. Thank you for watching it. If you want to know more details, please contact us! Thank you. #Tool #Training #Learning #Intermediate #en - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/numaker-m251sd Contact us: SalesSupport@nuvoton.com

Hello everyone! I am Chris, the Field Application Engineer from Nuvoton Technology. Today, I will introduce how to run a simple sample code on NuMicro M251/M252 series microcontroller. First, we connect the M251/M252 NuMaker development Board to the computer. Then click the M251/M252 BSP folder, click the Sample Code folder, template folder, Keil folder, and finally open the Template project file. What we are going to do is running a simple GPIO Toggle LED Sample Code. Introduce the main program briefly. First, set GPIO PB14 to Output Mode. After writing a small loop, set PB14 to reverse. Finally, set CLK_SysTickDelay to 300,000 microseconds (uSec). Before Rebuild, we must add the GPIO Source Code to the Library, find the corresponding Source Code and load it, and press Rebuild after it is complete. After the Rebuild, press Load and program the Code into the IC. When programing is over, press the reset button on the development board to confirm whether the LED lights are flashing on the board. That’s all for the tutorial of running sample code. Thank you for watching it. If you want to know more information, please feel free to contact us. #Tool #Training #Learning #Intermediate #en - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/numaker-m251sd Contact us: SalesSupport@nuvoton.com