Online Support

The NuMicro® M261 / M262 / M263 series is a low-power microcontroller platform based on Arm® Cortex®-M23 core for Armv8-M architecture. It runs up to 64 MHz with 512 Kbytes embedded Flash memory in dual bank mode supporting Over-The-Air ( OTA ) firmware update and 96 Kbytes embedded SRAM. It also supports low supply voltage from 1.8 ~ 3.6V and operating temperature range from - 40 ~ + 105 ℃.

Low power and robust security are two major vitals for Internet-of-Things ( IoT ) applications. The NuMicro® M261 / M262 / M263 series provides multi power modes for diverse operating scenarios, such as Power-down mode ( PD ), Fast Wake-up Power-down mode ( FWPD ), Low Leakage Power-down mode ( LLPD ), Ultra Low Leakage Power-down mode ( ULLPD ), Standby Power-down mode ( SPD ) and Deep Power-down mode ( DPD ). The NuMicro® M261 / M262 / M263 series also integrates RTC with independent VBAT voltage source pin to support low power mode with main power off and VBAT only. Regarding the power consumption of the NuMicro® M261 / M262 / M263 series, 97 μA / MHz ( LDO mode ) and 45 μA / MHz ( DC-DC mode ) in normal run mode, 2.8 μA in Standby Power-down mode, and less than 2μA in Deep Power-down mode without VBAT. It’s low power, wide supply voltage and fast wake-up features make it suitable for battery-powered IoT applications.

The NuMicro® M261 / M262 / M263 series provides secure boot function for a system developer to create a secure execution system in the microcontroller. The secure boot is a chain of secure process for verifying each software identity and integrity on the system. Secure boot can help to make sure that a device boots using only software that is trusted by the original developer. When the MCU starts, the firmware checks the signature of boot software, if the signatures are valid, the MCU boots, and the firmware gives control to the operating system. Otherwise, the system will not run at all.

The NuMicro® M261 / M262 / M263 series provides 4-region programmable eXecute-Only-Memory ( XOM ) to secure critical program codes. The AES 256 / 192 / 128 hardware accelerator and True Random Number Generator ( TRNG ) are built-in for data encryption. Up to six tamper detection pins are implemented to avoid malicious damage from hacker. Accompany with 96-bit Unique Identification ( UID ) and 128-bit Unique Customer Identification ( UCID ) to enhance the product security.

The NuMicro® M261 / M262 / M263 series integrates Voltage Adjustable Interface ( VAI ), up to 6 I / O pins to support the 2nd I / O voltage from 1.8 ~ 3.6V to save level shifter components while connecting to external devices.

The NuMicro® M261 / M262 / M263 series integrates one set of Secure Digital Host Controllers ( SDHC ), compliant with SD Memory Card Specification Version 2.0. It supports 50 MHz to achieve 200 Mbps at 3.3V operation, and dedicated DMA master with Scatter-Gather function to accelerate the data transfer between system memory and SD / SDHC / SDIO card.

The NuMicro® M261 / M262 / M263 series is equipped with plenty of peripherals such as Timers, Watchdog Timers, RTC, PDMA, External Bus Interface ( EBI ), Low-power UART, Universal Serial Control Interface ( USCI ), Quad SPI ( QSPI ), SPI / I²S, I²C, Smart Card Interface ( ISO-7816-3 ), GPIOs, up to 24 channels of PWM, makes it highly suitable for connecting comprehensive external modules and LED lighting control. The NuMicro® M261 / M262 / M263 series also integrates high performance analog front-end circuit blocks, such as one 16 channels of 12-bit 3.76 MSPS SAR ADC, two 12-bit 1 MSPS voltage type DAC, two rail-to-rail analog comparator ( ACMP ), temperature sensor, low voltage reset ( LVR ) and brown-out detector ( BOD ) to enhance product performance, reduce both external components and form factor.

The NuMicro® M262 series are all based on NuMicro® M261 series, it integrates USB 2.0 Full Speed On-The-Go ( OTG ) transceiver, compliant with USB OTG Supplement 2.0, can configurable as host-only, device only or ID-dependent. It also integrates USB 1.1 Host Controller and USB 2.0 Full Speed Device Controller. The NuMicro® M262 series supports crystall-less function that can generate precise frequency required by USB protocol without the need of external crystal, to reduce both the BOM cost and PCB size.

The NuMicro® M263 series are all based on NuMicro® M262 series, it supports one set of CAN 2.0B controllers, the bit rate can be programmed to values up to 1MBit/s. This CAN bus can be set to be one of six paired I / Os by PinConfigure.

The NuMicro® M261 series are suitable for classic IoT node devices, NuMicro® M262 series are suitable for connecting to USB host / device for data transfer, NuMicro® M263 series are suitable for industrial and automotive application that required CAN Bus for data communication.

The NuMicro® M261 / M262 / M263 series total provides 9 product part numbers. The package types of NuMicro® M261 / M262 / M263 series includes QFN33 ( 5 mm x 5 mm ), LQFP64 ( 7 mm x 7 mm) and LQFP128 ( 14 mm x 14 mm ). Pin-to-pin compatible in same package makes optimizing product features and performance easily.

Nuvoton NuMaker M261 / M262 / M263 evaluation boards ( NuMaker-M263KI ) and Nu-Link debugger are available for evaluation and product development. 3rd Party IDEs such as Keil MDK, IAR EWARM and NuEclipse IDE with GNU GCC compilers, are also supported.

Target Application:

  • Smart Home / Smart Home Appliance / Smart Door lock
  • Industrial Control / Industrial Automation
  • Smart City Facilities / Security Alarm System
  • IoT Device / Wireless Sensor Node Device / Communication Modules
  • Electronic Payments
  • Portable Wireless Data Collector
  • Handheld Medical Device

Key Features:

Operating Characteristics
  - Voltage range: 1.8 V ~ 3.6 V
  - Temperature range: -40 °C ~ +105 °C
   
Core
  - Arm® Cortex®-M23 processor, Armv8-M, runs up to 64 MHz
  - 32-bit hardware multiplier / divider
     
Memories
  - 512 KB Flash, dual bank, for OTA upgrade
  - 96 KB SRAM
  - 4 KB LDROM
  - 4 KB Key Protection ROM ( KPROM )
  - 4-region eXecute-Only-Memory ( XOM )
  - Supports Trusted Boot
     
Clocks
  - 4 ~ 24 MHz external high speed crystal oscillator ( HXT ) for precise timing operation
  - 32.768 kHz external low speed crystal oscillator ( LXT ) for RTC function and low-power system operation
  - 12 MHz internal high speed RC oscillator ( HIRC ) for system operation ( After auto-trim ± 0.25 % )
  - 48 MHz internal high speed RC oscillator ( HIRC48 ) for system operation ( After auto-trim ± 0.25 % )
  - 10 kHz internal low speed RC oscillator ( LIRC ) for Watchdog Timer and wake-up operation
  - 32 kHz internal low speed RC oscillator ( LIRC32 ) for RTC function
     
Power management
  - Dual voltage regulator is available for DC-DC converter or LDO
  - Supports 1.2 V and 0.9 V core voltage
  - Supports Power-down mode, Standby Power-down mode, Low Leakage Power-down mode, Ultra Low Leakage Power-down mode, Fast Wake-up Power-down mode, and Deep Power-down mode
  - Supports external power pin VBAT ( Standalone VBAT for RTC power domain )
     
   
Low Power Consumption
  - 97 μA / MHz ( LDO ) and 45 μA / MHz ( DC-DC ) in operating mode
  - 2.8 μA in Standby Power-down mode
  - Less than 2 μA in Deep Power-down mode without VBAT
     
RTC
  - 80 bytes of battery-powered backup registers, which can be cleared by tamper pins
  - Supports 6 static and dynamic tamper pins
     
Timers
  - Up to four 32-bit timers
     
PDMA
  - Up to 16 channels
PWM
  - Up to 24-channels PWM
  - Supports trigger ADC or DAC
  - Supports independent mode for PWM output / Capture input channel
  - Supports complementary mode for 3 complementary paired PWM output channel
   
Analog
  - Up to 16 channels 12-bit 3.76 MSPS ADC
  - Up to 2 sets of rail-to-rail comparators ( ACMP )
  - Up to 2 sets of 12-bit 1 MSPS voltage type DAC
  - Supports external VREF pin or internal reference voltage VREF: 1.6V, 2.0V, 2.5V, and 3.0V
     
Communication interfaces
  - Up to 6 sets of LPUART interface
  - Up to 3 sets of I²C interface
  - Up to 1 set of QSPI interface
  - Up to 4 set of SPI / I²S interface ( Configured as SPI or I²S )
  - Up to 3 sets of Smart Card Interface ( ISO-7816-3, ISO-7816-3 supports full duplex UART mode )
  - Up to 2 sets of USCI ( Configured as UART, SPI or I²C )
  - Up to 1 set of Secure Digital Host Controllers ( SDHC ), compliant with SD Memory Card Specification Version 2.0
  - 16 / 8-bits EBI ( External Bus Interface ) interface
     
VAI ( Voltage Adjustable Interface )
  - Up to 6 I / O pins to support the 2nd I / O voltage from 1.8 ~ 3.6V, applied voltage to the VDDIO pin
     
USB 2.0 Full Speed OTG (Crystal-less)
  - USB 2.0 Full Speed OTG (On-The-Go)
  - USB 1.1 Host Controller
  - USB 2.0 Full Speed Device Controller
     
CAN(Controller Area Network)
  - Supports 1 set of CAN 2.0B controller
  - Supports power-down wake-up function
     
Utility Support
  - Arm® Keil MDK and IAR EWARM IDE support for debugging
  - Free GNU compiler with NuEclipse IDE support
  - ICP ( In Circuit Programmer ) support for updating internal code via Nu-Link debugger
  - PinView for real time monitor the status of all IO pins
  - PinConfigure tool for pin assignment, initial code generation and OrCAD / Protel part generation
  - ClockConfigure tool for generating the initial source code of system clock
     
96-bit Unique ID ( UID )
     
128-bit Unique Customer ID ( UCID )
     
Packages
  - QFN33 ( 5 mm x 5 mm ), LQFP64 ( 7 mm x 7 mm ), LQFP128 ( 14 mm x 14 mm )
     
   

Share

Enter the Email address you like to share*
Your email*
Your name*
Validate Code*
Part No. Check Disty Flash SRAM Data Flash ISP ROM PDMA I/O Timer UART ISO-7816-3 Quad SPI SPI / I2S I2S SPI I2C CAN LIN EBI I2S/ AC97 USB OTG USB Host USB Device PWM Comparator DAC ADC Audio Codec Touch Key RTC Tamper Detect (pin) Voltage Adjustable Interface ISP/ICP/IAP Package Operating Temp. Range (°C ) Status SD Host Ethernet MAC Camera Interface QEI OP Amp. Crypto TRNG DES/ 3-DES / AES ECC SHA
M261KIAAE Check Disty None 512K 96K Configurable 4K 12 107 4*32-bit 6 3 - 1 4 1 3 - 2 - - - - 24*16-bit 2 2*12-bit 16*12-bit, Vref - - Y(VBAT) 6 Y ISP, ICP, IAP LQFP128 -40 to +105 Mass Production 1 - - 2 - Y Y Y Y Y
M261SIAAE Check Disty None 512K 96K Configurable 4K 12 51 4*32-bit 6 3 - 1 4 1 3 - 2 - - - - 24*16-bit 2 2*12-bit 16*12-bit, Vref - - Y(VBAT) 1 Y ISP, ICP, IAP LQFP64 -40 to +105 Mass Production 1 - - 2 - Y Y Y Y Y
M261ZIAAE Check Disty None 512K 96K Configurable 4K 12 25 4*32-bit 6 3 - 1 3 1 3 - 2 - - - - - 24*16-bit 2 2*12-bit 9*12-bit, Vref - - Y(VBAT) - Y ISP, ICP, IAP QFN33 -40 to +105 Mass Production 1 - - 1 - Y Y Y Y Y
M262KIAAE Check Disty None 512K 96K Configurable 4K 12 107 4*32-bit 6 3 - 1 4 1 3 - 2 - Y Y Y 24*16-bit 2 2*12-bit 16*12-bit, Vref - - Y(VBAT) 6 Y ISP, ICP, IAP LQFP128 -40 to +105 Mass Production 1 - - 2 - Y Y Y Y Y
M262SIAAE Check Disty None 512K 96K Configurable 4K 12 51 4*32-bit 6 3 - 1 4 1 3 - 2 - Y Y Y 24*16-bit 2 2*12-bit 16*12-bit, Vref - - Y(VBAT) 1 Y ISP, ICP, IAP LQFP64 -40 to +105 Mass Production 1 - - 2 - Y Y Y Y Y
M262ZIAAE Check Disty None 512K 96K Configurable 4K 12 25 4*32-bit 6 3 - 1 3 1 3 - 2 - - Y Y Y 24*16-bit 2 2*12-bit 9*12-bit, Vref - - Y(VBAT) - Y ISP, ICP, IAP QFN33 -40 to +105 Mass Production 1 - - 1 - Y Y Y Y Y
M263KIAAE Check Disty None 512K 96K Configurable 4K 12 107 4*32-bit 6 3 - 1 4 1 3 Y 2 - Y Y Y 24*16-bit 2 2*12-bit 16*12-bit, Vref - - Y(VBAT) 6 Y ISP, ICP, IAP LQFP128 -40 to +105 Mass Production 1 - - 2 - Y Y Y Y Y
M263SIAAE Check Disty None 512K 96K Configurable 4K 12 51 4*32-bit 6 3 - 1 4 1 3 Y 2 - Y Y Y 24*16-bit 2 2*12-bit 16*12-bit, Vref - - Y(VBAT) 1 Y ISP, ICP, IAP LQFP64 -40 to +105 Mass Production 1 - - 2 - Y Y Y Y Y
M263ZIAAE Check Disty None 512K 96K Configurable 4K 12 25 4*32-bit 6 3 - 1 3 1 3 Y 2 - - Y Y Y 24*16-bit 2 2*12-bit 9*12-bit, Vref - - Y(VBAT) - Y ISP, ICP, IAP QFN33 -40 to +105 Mass Production 1 - - 1 - Y Y Y Y Y

User Feedback

Please rate our website
Email
Name*
Validate Code*

微信扫一扫,关注新唐MCU。

Login myNuvoton

to stay informed of any changes to the documents you download.
If you don't want to login, just close this page and download directly.