NuMaker-Volcano is the development board for Nuvoton NuMicro® M0A21/M0A23 microcontrollers. This board stands out with its compact size of only 2.5x5 millimeters, slightly larger than a coin. It comes equipped with the powerful M0A23 microcontroller, and all 28 pins are accessible for circuit board connections. Additionally, it features a Nu-Link2-Me for programming and debugger purposes. NuMaker-Volcano serves as a versatile platform for evaluating, developing, and validating industrial and automotive applications. #AEC-Q100 #125degree #Volcano #Microcontroller #Automotive #MCU #Nuvoton #NuMicro #M0A23 #Basic #Product #learning #en - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC buy now: https://direct.nuvoton.com/ contact us: SalesSupport@nuvoton.com

Nuvoton NuMicro Family microcontroller I2C basic function introduction. Use M031/M032 Series as an example. #Training #Basic #en #Learning - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC buy now: https://direct.nuvoton.com/ contact us: SalesSupport@nuvoton.com

Hello everyone. Welcome back to Nuvootn’s YouTube channel. This is a reference design of a thermostat made by Nuvoton. The first screen shows the current room temperature of 25 degrees Celsius. You can also set your target temperature through the control panel. The middle switch is the power switch of temperature control. Press the Temperature icon and you can adjust backlight brightness by slide control. Back to the function page, press the Snow icon where you can change the strength of the air conditioner. You can increase or decrease the strength by these up and down arrows or you can press the snow icon for adjustment. Changing the heater, dehumidifier, and fan are the same. The third page is a calendar where you can set the date to book opening and closing the temperature control. What you saw is the reference design introduction. Now let’s talk about the composition of the board. In the middle of the board is a Nuvoton N9H20 main control chip. This main control chip has built-in 32 Mbytes DDR so the board is very clear and the hardware design is easy. At the top side, there is a 1 Gbits NAND Flash for code and pictures storage. At the bottom left there is a connector to the UART control interface. In the middle left area, there is a 5 Voltage (Micro USB) power input. In the upper right corner, there is an RS485 connection. Through this green connector, you can connect to RS485 for fans, air conditioners, and other devices' control. In the lower right corner, there is a chip for power IC and some other parts. The application reference design is concise and powerful. That’s all for the hardware introduction. Thank you for watching. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC buy now: https://direct.nuvoton.com/tw/ contact us: SalesSupport@nuvoton.com #Product #Application #Learning #Intermediate #en

Nuvoton announced the latest ML51/ML54/ML56 microcontroller, built-in capacitive touch sensing, LCD driver highly integrated low power platform. Based on 1T 8051 core, running up to 24MHz, the power consumption in normal run mode is 80uA/MHz, lower than 1uA in power down mode the power consumption while power down with LCD on is lower than 20uA. 0:00 intro 0:37 NuMicro 8051 Microcontroller 1:38 ML51/ML54/ML56 Product Portfolio 2:18 ML51/ML54/ML56 Features 3:27 Broad Scalability 4:05 Provide 4 Different Power Modes 4:44 LCD Driver Feature 5:52 Touch Key Features 7:05 Target Applications #Product #Learning #Basic #en #ML51 #ML54 #ML56 #8051 #LowPower #LCD-Driver #HumanMachineInterface #HMI #TouchKey-IC #HomeAppliance #EmbeddedWorld2022 - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.com

以新唐 NuMaker NUC980 IIoT 為平台，使用 Linux 進行開發，學習開發各式功能，觀看本片，您將學會如何控制 GPIO 使 LED 閃爍。 哈囉大家好，我是新唐工程師 Kevin，今天為大家介紹如何在 NuMaker NUC980 IIoT 板子上透過 GPIO 讓 LED 燈閃爍。 NuMaker NUC980 IIoT 板子的 Power-on Setting上方有 3 個 LED 燈，分別由不同的 GPIO 控制。最左邊，編號 LED03 的 LED 燈是由 GPIO B8 這根 pin 控制。今天示範如何用程式控制 GPIO B8 讓 LED 燈閃爍。 這是 LED 燈閃爍的程式，在看程式之前，我先為各位說明，在 Linux kernel 中，每一根 GPIO pin 都有編號。每一個 GPIO Group 占用 32個編號，編號為 0 到 31，分配給 GPIO Port A 這個 group，編號 32 到 63 分配給 GPIO Port B，以此類推。 LED03 這個 LED 燈是由 GPIO B8 這根 pin 控制，GPIO B8 在 Linux 中的編號是 40。 回到程式中，我們看到這個程式是透過 system function 執行系統命令，透過 Linux kernel 的 sysfs 控制 GPIO。 第 23 行 system("echo40 /sys/class/gpio/export"); 是將 GPIO B8 設定成可以用sysfs 控制。 第 24 行 system("echo out /sys/class/gpio/gpio40/direction"); 是將 GPIO B8 設定為 output。 接下來在 while loop 中，透過 system("echo 1/sys/class/gpio/gpio40/value"); 讓 GPIO B8 輸出 high；再透過 system("echo 0 /sys/class/gpio/gpio40/value"); 讓 GPIO B8 輸出 low，中間延遲 1 秒鐘，就可以做到 LED 燈閃爍的功能。 這個程式，main.c，儲存後，進行 compile 輸入 arm-linux-gcc main.c -o gpio_toggle (輸入 ls) 產生一個執行檔 gpio_toggle 將 gpio_toggle 拷貝到 root file system 目錄中， (輸入 sudo cp gpio_toggle ../rootfs) 然後重新 compile Linux Kernel 透過 NuWriter 將 Linux kernel 下載到NuMaker NUC980 IIoT 板子上執行 Linux Kernel 開機完成後，輸入 ./gpio_toggle，執行閃爍 LED 的程式。 此時可以看到 NuMaker NUC980 IIoT 板子上的 LED 正在閃爍。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/numaker-nuc980-iiot 聯絡我們： SalesSupport@nuvoton.com

本方案使用 NuMicro M480 高效能 M4 微控制器，搭配 emWin library 進行 GUI 圖像化人機介面設計，將結果顯示在 2” OLED 上。NuMicro M480 系列微控制器是新唐的最新產品，透過這個系列產品高達 192 MHz 的強大運算能力和多達 160 KB 的 SRAM，並且搭配 2 吋 OLED 螢幕，來達到流暢地解碼及播放 GIF 動態影像，那這個方案包含了三大重點： 第一點：我們使用了新唐 M480 高效能微控制器，透過高速 SPI 控制 OLED 來顯示炫麗的動態效果 第二點：本方案已內建 GIF 解碼和多種字型的 Library，如果有其他字型需求，可以透過新唐字型轉換工具載入其他字庫，再加上 emWin Library 的使用，快速開發完成高質感使用者介面。 第三點：本方案可以應用於有顯示功能需求的產品，如電競主機板，可以高效地動態顯示溫度、風扇轉速和硬碟狀態等 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 聯絡我們：SalesSupport@nuvoton.com ---- Today we are going to introduce our reference design OLED Display with GIF Format Decode featuring the NuMicro M480 series microcontroller. As you can see, the microcontroller controls the 2-inch OLED screen and GIF files can be played on it. The M480 series runs up to 192 MHz with 512 KB embedded Flash memory and 160 KB embedded SRAM. The high-performance MCU decodes GIF motion graphics smoothly. There are three major features about this reference design: First: We use the Nuvoton M480 high-performance microcontroller to control the OLED through high-speed SPI to showcase dynamic effects. Second: This solution has built-in GIF decoding and various font libraries. If there are other font requirements, you can load other fonts through the Nuvoton font conversion tool, and use the emWin Library to develop a high-quality user interface quickly. Third: It can be applied to products requiring display functions, such as e-sports motherboards, which can dynamically display temperature, the speed of the fan and the status of the hard disk. The OLED device has a 2-inch OLED screen with a resolution of 256*64. There is an SD card slot underneath, which obviously is for data storage and the storage status is shown on the OLED screen. The right side, there is a high-speed USB for PC connection as a flash drive. A headphone jack is on the left, I’m sure you all know how it works.

新唐32位Cortex-M0 Nano112超低功耗單片機之产品应用方案介紹

NuMicro® Family ARM Cortex™ -M0 32位MCU NUC100 Series I2C

Nuvoton M051 Series 技術研討

NUC123技術研討