Nuvoton announced the latest ML51/ML54/ML56 microcontroller, built-in capacitive touch sensing, LCD driver highly integrated low power platform. Based on 1T 8051 core, running up to 24MHz, the power consumption in normal run mode is 80uA/MHz, lower than 1uA in power down mode the power consumption while power down with LCD on is lower than 20uA. 0:00 intro 0:37 NuMicro 8051 Microcontroller 1:38 ML51/ML54/ML56 Product Portfolio 2:18 ML51/ML54/ML56 Features 3:27 Broad Scalability 4:05 Provide 4 Different Power Modes 4:44 LCD Driver Feature 5:52 Touch Key Features 7:05 Target Applications #Product #Learning #Basic #en #ML51 #ML54 #ML56 #8051 #LowPower #LCD-Driver #HumanMachineInterface #HMI #TouchKey-IC #HomeAppliance #EmbeddedWorld2022 - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.com

新唐科技推出最新集成控制、電容式觸控、驅動液晶顯示器 (LCD) 的三合一低功耗微控制器 - Nuvoton NuMicro ML51/ML54/ML56 系列，採用 1T 8051 嵌入式核心，最高速可達 24 MHz，在正常運行模式典型功耗可達 80 uA/MHz，休眠模式功耗可低於 1 uA，當休眠模式 LCD 開啟之功耗可低至 20 uA。ML51/ML54/ML56 系列提供配置 16/32/64 KB Flash 與1/2/4 KB SRAM，提供 10 腳至 64 腳多樣的封裝，內建高達 14 個的觸控按鍵硬體支援自動掃描與校準功能，節省外部元件並縮小產品體積，在休眠模式下平均功耗不到 2 uA 即可實現 14 個觸控按鍵的偵測。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/low-power-8051-series/ 聯絡我們： SalesSupport@nuvoton.com #Product #Learning #Basic #zh-Hant

介紹與說明 Nuvoton NuMicro ML56 電容式觸控按鍵基本原理和感應方法。 哈囉大家好! 我是新唐 FAE Tim，今天為大家介紹 ML56 電容式觸控按鍵技術。 首先介紹 #電容式觸控按鍵基本原理。 在沒有手指觸摸的傳感器的電容稱為 “寄生電容” CP 。 寄生電容是由傳感器 (包括傳感器，走線和過孔) 與系統中其他導體 (例如接地層，走線，產品機構或外殼中的任何金屬等) 之間的電場所產生的。 傳感器和手指之間的電容為 CF，傳感器的總電容 CT 是 CP 和 CF 之和。 接著要說明 ML56 #電容式觸控按鍵感應方法。 ML56 實現了兩個可變電容器組，用於向 CP (或 CT) 和 CR 注入電荷。 CR 是參考通道的寄生電容，在觸控按鍵校正之後，CP 和 CR 與 CB 和 CCB 保持平衡 (比較器輸出為 “低準位”) 。 手指觸摸在目前偵測的觸控按鍵，導致 CT = CP + CF，使比較器的負輸入端電壓低於正輸入端，並且比較器輸出為 “高準位”。 ML56 觸控按鍵控制器會將 CCB 增加到 CCB’，以使 CT 和 CR 再次達到平衡 (比較器輸出為 “低準位”)。透過檢查 CCB 和 CCB’ 之間的差異，可以做手指觸摸的偵測。 CCB 增加到 CCB’ 的數值與預定的觸控門檻值來做比較，演算法可以確定觸控按鍵處於 ON (觸摸) 狀態還是 OFF (無觸摸) 狀態。 以上是這次的教學影片, 謝謝大家！ 如果您有任何問題，歡迎聯絡我們。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/low-power-8051-series/ 聯絡我們： SalesSupport@nuvoton.com #Product #Learning #Basic #zh-Hant

介紹與說明 Nuvoton NuMicro ML56 電容式觸控按鍵電路板設計。 哈囉大家好！我是新唐 FAE Tim。 今天為大家介紹 ML56 電容式觸控按鍵電路板設計。 首先介紹觸控傳感器通道選擇。 #觸控傳感器通道 ML56 系列最多支援 14 個觸控傳感器通道。 #參考傳感器 建議選擇觸控傳感器通道 TK7 或 TK14 當作參考傳感器。 加大參考傳感器和其他信號之間的距離，以降低互相干擾的機會。 #屏蔽電極 將屏蔽電極圍繞在觸控傳感器周圍，可以有更好的信號品質和防水能力。 建議選擇觸控傳感器通道 TK0, TK4 或時脈輸出腳位 (P3.2/ P4.6/ P5.7) 當作屏蔽通道。 接著要說明 PCB 佈局規則。 #觸控按鍵形狀 建議傳感器面積為 10 x 10 mm，以實現良好的觸控按鍵靈敏度。 觸控傳感器的電極越大，外殼厚度可以越厚。 #參考傳感器 建議選擇觸控傳感器通道 TK7 或 TK14 當作參考傳感器。 加大參考傳感器和其他信號之間的距離，以降低互相干擾的機會。 一般情況下，建議使用直徑為 1 mm 大小的圓形電極。 #接地 建議觸控按鍵的走線具有良好的網地圍繞。 建議觸控按鍵下方要鋪網地。 鋪網地的規格為 6 mil 的走線和 50 mil 的網格。 #屏蔽電極 將屏蔽電極圍繞在觸控按鍵周圍，用於在觸控按鍵周圍提供同相位的信號。 網狀屏蔽電極的規格為 6 mil 的走線和 50 mil 的網格。 屏蔽電極區域到觸控按鍵周圍的寬度需要大於 10 mm。 #觸控按鍵外殼厚度 隨著外殼厚度的增加，觸控按鍵的靈敏度將降低。 觸控按鍵尺寸越大，外殼能做得越厚。 建議的觸控按鍵直徑尺寸與搭配的壓克力外殼厚度如表所示。 以上是這次的教學影片，謝謝大家！ 如果您有任何問題，歡迎聯絡我們。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/low-power-8051-series/ 聯絡我們： SalesSupport@nuvoton.com #Product #Learning #Basic #zh-Hant

新唐科技推出最新集成控制、電容式觸控、驅動液晶顯示器 (LCD) 的三合一低功耗微控制器 - Nuvoton NuMicro ML56 系列，並提供一電容式觸控與驅動液晶顯示器解決方案程式庫。此影片將會介紹 API 的功能、參數及回傳值並且最後則會講解如何使用 BSP 裡的範例程式搭配 NuMaker-ML56SD 來開發您的第一個電容式觸控與驅動液晶顯示器的應用程式。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/low-power-8051-series/ 聯絡我們： SalesSupport@nuvoton.com #Product #Learning #Basic #zh-Hant

新唐科技提供一電容式觸控解決方案調適工具 (NuSenadj)，此調適工具最大的特點為可通過一人機介面針對不同的機構來自動調整參數，並將參數匯出並複製至其他開發板。不僅能大大縮短開發人員的開發時程，也可縮短量產時間。此影片將會介紹如何使用此調適工具以及各個參數代表的意義。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/low-power-8051-series/ 聯絡我們： SalesSupport@nuvoton.com #Product #Learning #Basic #zh-Hant

介紹與說明 Nuvoton NuMicro ML56 電容式觸控按鍵防水與抗干擾。 哈囉大家好! 我是新唐 FAE Tim，今天為大家做 ML56 觸控按鍵防水與抗干擾介紹。 首先介紹 ML56 觸控按鍵防水與抗干擾的能力。 良好的防水能力，在 2 mm 深度的積水下觸控按鍵動作仍正常。 通過 IEC 61000-4-6 10 V 動態注入電流測試。 接著要說明 ML56 觸控按鍵的相關參數設定，先說明觸控靈敏度。 #Pulse Width (觸控按鍵感測脈衝寬度時間控制） 可以透過適當設定脈衝寬度來調整觸控按鍵的靈敏度，較短的脈衝寬度設定會帶來較差的靈敏度和較低的功耗，反之亦然。 接著說明觸控性能的穩定性之 1 #Times (觸控按鍵感測次數控制) 可以透過適當地設置 “次數” 來調整觸控按鍵原始數據的穩定性，“次數” 設置越短，原始數據的穩定性越差，功耗也越低，反之亦然。 觸控性能的穩定性之 2 #IIR (IIR 濾波器) IIR 濾波器可以控制當前原始數據與上一個原始數據的比率。 用戶可以啟用 IIR 濾波器以抗干擾。啟用 IIR 濾波器時，它將增加觸控響應時間。 觸控性能的穩定性之 3 #Debounce (觸控按鍵去抖動) 可以透過適當地設置去抖動，觸控按鍵進入 (開) 和釋放 (關) 偵測的去抖動次數來調整觸控按鍵的穩定性，較短的去抖動設置會帶來更快的觸控響應時間，反之亦然。 觸控性能的穩定性之 4 #Trace Baseline (基準線是透過 “校正” 所產生的) 觸控按鍵自動環境補償是一種演算法，該演算法可在啟動運作時自動追蹤基準線做環境變化補償，使觸控按鍵性能更加穩定。綜合上述的參數說明，以下為大家介紹防水與抗干擾的參數設定。 首先是 #防水參數設定。 良好的防水能力，在 2 mm 深度的積水下觸控按鍵動作仍正常。 觸控按鍵系統參數如表所示： Pulse Width = 500 ns Times = 128 接著是 #抗干擾性參數設定 通過 IEC 61000-4-6 10 V 動態注入電流測試。 觸控按鍵系統參數如表所示： Pulse Width = 2 us Times = 128 IIR New = 6, Old = 2 Debounce Entry = 1, Release = 1 接著我們使用 ML56 NuMaker Board 來為大家做實際操作展示 #觸控按鍵防水功能。手指先沾水，然後去觸摸觸控按鍵，反覆以上動作，可以看到觸控按鍵依舊正常動作，不受影響。 最後我們使用 ML56 NuMaker Board 來為大家做實際操作展示 #觸控按鍵抗干擾能力。先打開對講機，然後近距離干擾觸控按鍵，可以看到觸控按鍵依舊正常動作，不受影響。 以上是這次的教學影片, 謝謝大家! 如果您有任何問題，歡迎聯絡我們。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/low-power-8051-series/ 聯絡我們： SalesSupport@nuvoton.com #Product #Learning #Basic #zh-Hant

Hello! Everyone! I am Nuvoton FAE Tim. Today, I will show you ML56 Capacitive Touch Key Technology. First introduce the Capacitive Touch Key Fundamentals. The capacitance of the sensor without a finger touch is called as “parasitic capacitance”, CP. Parasitic capacitance results from the electric field between the sensor (including the sensor pad and traces) and other conductors in the system such as the ground planes, traces, any metal in the product’s chassis or enclosure, etc. The capacitance between the sensor pad and the finger is CF. The total capacitance CT of the sensor is the sum of CP and CF. Next, we will explain the ML56 Capacitive Touch Key Sensing Method. ML56 implements two switching capacitor banks for injecting charges to CP (or CT) and CR. CR is the parasitic capacitance of reference channel. After touch key calibration, CP and CR are balanced with CB and CCB (comparator output is “low”). Touch the sensing touch key which makes CT = CP + CF Now the negative input terminal voltage of the comparator is lower than positive side and comparator output is “high”. ML56 touch key controller will increase CCB to CCB’ to balance CT and CR again (comparator output is “low”). A finger touch can be detected by checking the difference of CCB and CCB’. By comparing the CCB’ shift level from CCB, the steady state to a predetermined threshold, the algorithm can determine whether the touch key is in ON (Touch) or OFF (No Touch) state. That's all for today's video, thank you everyone! If you have any questions, please contact us. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Hello! Everyone! I am Nuvoton FAE Tim. Today, I will show you ML56 Capacitive Touch Key PCB Design. First introduce the Touch Sensor Channel Selection. Touch Sensor Channels. ML56 series supports up to 14 touch sensor channels. #Reference Sensor It is recommended to select one reference sensor at touch sensor channel TK7 or TK14. Maximize the distance between the reference sensor and other signals to minimize crosstalk. #Shield Electrodes Put the shield electrode around the touch sensor to get better signal quality and waterproof capability. Recommended to select shield channel at touch TK0, TK4 or clock out pins (P3.2 / P4.6 / P5.7). Next, we will explain the PCB Layout Rules. #Touch Key Shapes Recommended to have a 10 x 10 mm sensor area for good touch key sensitivity. Larger touch sensor electrode work better for thicker cover. #Reference Sensor Recommended to assign the reference key at touch channel TK7 or TK14. Maximize the distance to other signals to minimize crosstalk. Round shape electrode with 1 mm diameter size is enough for normal case. #Ground Plane It is recommended that the traces of the touch key have a good hatched ground plane surround. It is recommended to have hatched ground plane under the touch keys. Hatched ground plane with 6 mil trace and 50 mil grid. #Shield Electrode Put touch keys with shield electrode around which provides the same phase signal around touch keys. Hatched shield electrode with 6 mil trace and 50 mil grid. Shield electrode area needs to keep filled around the touch key in greater than 10 mm width. Finally, explain the Touch Key Cover Thickness. As the cover thickness increases, the touch key sensitivities will decrease. Larger touch key size work better for thicker cover. Recommended touch key diameter size with difference acrylic cover thickness as shown in the table. That's all for today's video, thank you everyone! If you have any questions, please contact us. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Nuvoton announced the latest ML56 microcontroller, built-in capacitive touch sensing, LCD driver highly integrated low power platform. And provides capacitive touch sensor and LCD driver library. The solution is delivered through the API guide, which includes details on each function call, parameters and returns. Finally, this video provides an overview on how to develop a custom touch key and LCD application from the BSP release. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Nuvoton provides a development tool for capacitive Touch Sensors. The best feature of the calibration tool is that it uses the GUI to configure and tune your design automatically. Besides, the tool can export the configuration parameters and import them to another. Not only can greatly shorten the development time of developers, but also shorten the time for mass production. This video will introduce how to use this development tool and the definition of parameter. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

Introduce the waterproof and noise immunity of ML56 touch key. Hello! Everyone! I am Nuvoton FAE Tim. Today, I will show you the waterproof and noise immunity of ML56 touch key. First introduce the waterproof and noise immunity of ML56 touch key. Good waterproof function, support finger touch with 2 mm depth water droplet. IEC 61000-4-6 conducted noise immunity (CNI) with 10 Vrms noise voltage. Next, we will explain the related parameter settings of the ML56 touch key, and first explain the touch sensitivity. #Pulse Width (Touch key sensing pulse width time control) Touch key sensitivity can be adjusted by setting Pulse Width properly, shorter Pulse Width setting comes with poor sensitivity and less power-consumption, vice versa. Then explain the stability of touch performance, Part 1. #Times (Touch key sensing times control) Touch key raw data stability can be adjusted by setting Times properly, shorter Times setting comes with poor raw data stability and less power-consumption, vice versa. Stability of touch performance, Part 2. #IIR (IIR filter) IIR filter can control the ratio of current raw data and previous one. User can enable IIR Filter to be against noise. It will increase the touch response time when enables IIR Filter. Stability of touch performance, Part 3. #Debounce (Touch key debounce) Touch key stability can be adjusted by setting Debounce properly, the debounce times for touch key entry (on) and release (off) detection, shorter Debounce setting comes with faster touch response time, vice versa. Stability of touch performance, Part 4. #Trace Baseline (Baseline is generated by “Calibration”) Touch key auto environment compensation is an algorithm that baseline tracking each touch key automatically at power-up and keeps compensating environment variation affects touch key performance during runtime. Based on the above parameter description, the following introduces the waterproof and noise immunity parameter settings. The first is waterproof parameter setting. Good waterproof function, support finger touch with 2 mm depth water droplet. Touch key system parameters are shown in the table Pulse Width = 500 ns Times = 128 Next is the noise immunity parameter setting IEC 61000-4-6 conducted noise immunity (CNI) with 10 Vrms noise voltage. Touch key system parameters are shown in the table. Pulse Width = 2 us Times = 128 IIR New = 6, Old = 2 Debounce Entry = 1, Release = 1 Then we use the ML56 NuMaker Board to show you the waterproof function of the touch key. Dip the finger in water first, and then touch the touch key. Repeat the above actions, we can see that the touch key still works normally and is not affected. Finally, we use the ML56 NuMaker Board to show you the noise immunity ability of the touch key. Turn on the walkie-talkie first, and then interfere with the touch key at close range, we can see that the touch key still operate normally and is not affected. That's all for today's video, thank you everyone! If you have any questions, please contact us. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.comon.com #Product #Learning #Basic #en

This video is going to show you our latest Low power ML51 series microcontroller. The ML51 platform features high performance and pin-to-pin compatibility with our 32-bit microcontrollers, such as M480, M031, and M261 series . ML51 series supports up to 24MHz operation frequency, and 1.8V to 5.5V operating voltage, it provides four power modes: normal run mode, low power run mode, low power idle mode, and power down mode. In power down mode with multiple wake-up sources. The power consumption in low power idle mode is down to 13 μA and in power down mode it is less than 0.8 μA. When the clock runs at internal RC oscillator can also allow 9600 baud rate for UART communication. ADC supports up to 8 channels of 12-bit ADC, analog comparator and five levels of the internal reference voltage, ML51 provide two channels of PDMA, strong immunity like 8 kV ESD and 4.4 kV EFT. - For more information, please visit: http://www.nuvoton.com buy now: NuMaker-ML51PC/ http://direct.nuvoton.com/numaker-ml51pc NuTiny-ML51EB9AE/ http://direct.nuvoton.com/nutiny-ml51eb9ae contact us: SalesSupport@nuvoton.com #Product #Learning #Basic #en

Tubular motors can be easily seen everywhere such as curtains, rolling doors, and automatic clothes racks. As the concept of home automation is spreading widely, those products become more and more popular. Nuvoton provides completed platform, ML51 series for different needs of tubular motors. It’s based on 1-T 8051 core, running up to 24 MHz core speed. It provides 12-bit ADC detecting motor current and up to 2 sets of analog comparators for overcurrent and overvoltage protection. Much higher safety features for the tubular motors are realized. 105-degree high-temperature resistance makes it suitable for control box exposed outdoors. As for the multiple noises and inference environment, ML51 series provides strong immunity like 8 kV ESD and 4.4 kV EFT. Hello, everyone, welcome back to Nuvoton’s YouTube channel, I am the product manager of microcontrollers. Today I am going to show you our successful story, home automation with the Tubular motor, which adopts our latest industrial microcontroller, ML51 series. Today the topic we are going to talk about is the home automation and motorization system for curtain and doors. These tubular motors can be easily seen around everywhere, like curtain, rolling door, garage door, and automatic clothes rake…and so on. As the concept of home automation is spreading widely, those products are more and more popular. For example, the automatic curtain is popularly applied in hotel, new building, hospital and new store, why is this product become more and more popular? Lazy economy becomes a new type of consumption demand, people pursue a time-saving and labor-saving product, imagined if you have an emitter to control curtain automatically, and smart adjustment with the brightness of outdoor. And the new product hit the shelf is automatic clothes rake, now this new product is not only a hanger but also integrated with UV light disinfection, heating function and fan controller. About the garage door, now integrated more security function, such as overcurrent protection for device longevity, infrared system can be added to increase anti-pinch security. Nuvoton provides completed platform, ML51 series for different needs of tubular motors. It’s based on 1-T 8051 core, running at 24MHz core speed, provides 12-bit ADC can detect motor current, up to 2 sets of analog comparator to have overcurrent and over voltage protection so can provide much higher safety feature for the tubular motors. ML51 series also provide from 1.8V to 5V power supply, so whether the AC power or the battery supplied can easily be adapts to different power source. This series has up to 105-degree high temperature resistance, which also can be very suitable for control box explore at outdoors. As for the multiple noise and inference environment, ML51 series provides strong immunity like 8 kV ESD and 4.4 kV EFT. Nuvoton provides an easy-to-use development environment, which includes NuMaker board, Nu-Link, BSP and sample codes, those tools can help you shorten your development cycles. On the backside of each development board, you can find the website which the comprehensive information is available. Nuvoton has some successful case in China and Europe. We hope to have more new opportunities after releasing this video. Thanks for watching, if you like this video please give it a thumbs up, if you have any question can also leave a message at bottom, we will have personal to reply the question soon. The ML51 NuMaker boards are now available at Nuvoton official eStore direct.nuvoton.com. Thank you again for staying with us. Hope to see you soon. Bye~ For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC buy now: NuMaker-ML51PC/ http://direct.nuvoton.com/numaker-ml51pc NuTiny-ML51EB9AE/ https://direct.nuvoton.com/tw/nutiny-ml51eb9ae contact us: SalesSupport@nuvoton.com

新唐科技於 7/9 下午兩點舉辦線上研討會，產品經理 Jenny 對低功耗系列產品做詳盡介紹，包含產品系列組合、特點、成功應用案例，還有開發板一折特賣。Jenny 與 SAE 也在直播現場回答問題。 #product #application #webinar #general #zh-Hant - 0:00 新唐科技公司與完整生態系簡介 13:55 低功耗工業級8051微控制器 31:43 NuMaker溫控器初亮相 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 聯絡我們： SalesSupport@nuvoton.com

低功耗8051產品低功耗運行模式特色介紹。ML51系列工具及應用推薦。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/ml51-series/ 聯絡我們： SalesSupport@nuvoton.com

新唐低功耗8051微控制器 - ML51 系列 產品、應用及開發環境介紹。 ML51 平台的速度高達 24 MHz。並具有 1.8 ~ 5.5V 的寬工作電壓，同時功耗也提供非常低，在正常運行模式下功耗僅需 80 μA / MHz，在休眠模式下功耗更可以低至 0.8 μA；類比部分我們提供 8 組 12 位 ADC、2 組比較器以及 5 階內置參考電壓。另外我們也內建 2 組 PDMA，ESD 部分可以高達 8 kV 以及 EFT 可以高達 4.4 kV，我們還提供許多豐富週邊、像是三路串口以及 2 路 I2C 還有 2 路 SPI。 ML51 系列適合於在各種需要電池的裝置，舉例來說，我們可以讓一個225mAh 的鈕扣電池持續工作 3 年而不需要更換電池。另外我們提供的寬工作電壓可以供電低至 1.8V 也不需要外加 LDO 在 PCB 板、舉例像是 TWS 的無線藍芽耳機或者是獨立式的煙霧感測器都是非常適合 ML51 的產品。 ML51 提供的開發板可以直接與電腦相連，不需要額外的燒錄器。ML51 提供的開發板以及相關的 sample code 都能讓各位快速上手、另外我們新的開發板上面，背面都印有一個短網址、輸入短網址進入網頁後可以在上面找到相關的開發資訊。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買網址： NuMaker-ML51PC/ http://direct.nuvoton.com/numaker-ml51pc NuTiny-ML51EB9AE/ http://direct.nuvoton.com/nutiny-ml51eb9ae 聯絡我們：SalesSupport@nuvoton.com This video is going to show you our latest Low power ML51 series microcontroller. The ML51 platform features high performance and pin-to-pin compatibility with our 32-bit microcontrollers, such as M480, M031, and M261 series . ML51 series supports up to 24MHz operation frequency, and 1.8V to 5.5V operating voltage, it provides four power modes: normal run mode, low power run mode, low power idle mode, and power down mode. In power down mode with multiple wake-up sources. The power consumption in low power idle mode is down to 13 μA and in power down mode it is less than 0.8 μA. When the clock runs at internal RC oscillator can also allow 9600 baud rate for UART communication. ADC supports up to 8 channels of 12-bit ADC, analog comparator and five levels of the internal reference voltage, ML51 provide two channels of PDMA, strong immunity like 8 kV ESD and 4.4 kV EFT.

As a leading supplier of 8051 microcontrollers (MCUs) , Nuvoton offers a variety of products with the best performance critical to the success of consumers and industrial products. NuMicro® 8051 industrial series microcontrollers is based on 1T 8051 core, running up to 24 MHz, with up to 32 Kbyte of Flash memory and up to 2 Kbyte of SRAM. It supports one high precision 24 MHz allowing ± 1 % deviation and one 10 kHz internal RC Oscillators, operating at 2.4 V ~ 5.5 V voltage and - 40 ℃ ~ 105 ℃. NuMicro® 8051 industrial series is equipped with special features such as up to 15 channels of 500k SPS 12-bit ADC, up to 12 channels of PWM with independent counters and GPIO supports 20 mA driving capability, also with ESD resistivity 8 kV and EFT resistivity 4.4 kV. Combined all these above high performance features, and provides 10-33 pin packages for a broad range of applications.

The ML51 is a Flash embedded 1T 8051-based microcontroller. The instruction set of the ML51 is fully compatible with the standard 80C51 with performance enhanced and low power consumption. The ML51 runs up to 24 MHz at a wide voltage range from 1.8V to 5.5V, and contains up to 64/32/16/8 Kbytes Flash called APROM for programming code. The ML51 Flash supports In-Application-Programming (IAP) function, which enables on-chip firmware updates. The ML51 includes an additional configurable up to 4/3/2/1 Kbytes Flash area called LDROM, in which the Boot Code normally resides for carrying out the In-System-Programming (ISP). - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC buy now: https://direct.nuvoton.com/tw/ml51-series/ contact us: SalesSupport@nuvoton.com #Product #Learning #Basic #en 0:00 簡介 0:20 Agenda 0:45 NuMicro Product Portfolio 1:28 2019 Brand New MCU Platform 2:06 ML51/ML54/ML56 Series Portfolio 3:29 ML51 Series Low 4:50 NuMicro Naming Rule 6:06 NuMicro® ML51 Features 8:19 4 Different Power Modes 10:44 Low Power Mode Features • Wake up resource: WKT, ACMP, GPIO 12:37 Low Power VS Battery Life 13:28 ADC 15:00 Comparison of 8-bit Products Feature 17:13 Fire Fighting System 21:30 Battery Management System (BMS) 22:30 Gaming Phone 23:36 Development Board 24:13 Development Environment

新唐科技推出工業級 的 NuMicro MS51 系列微控制器，為客戶提供更精巧，更簡潔的封裝以滿足簡單控制又需工業級微控制器的產品需求。 NuMicro MS51 系列採用 1T 8051 嵌入式核心，工作電壓為 2.4V ~ 5.5V，並符合 -40℃ 至 105℃ 的工業級操作溫度，內置一個 10KHz 與一個 24MHz 的高低速振盪器，常溫下可達 1% 精準度而不須外接晶振，此外 GPIO 具備 20mA 高電流驅動幫助節省外圍器件，並擁有 8kV ESD、4.4kV EFT 高抗干擾能力。 #Product #Learning #Basic #zh-Hant - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/ms51-series-1t/ 聯絡我們： SalesSupport@nuvoton.com

新唐 PM Jenny 和 SAE 卉蓁帶大家深入探索 MS51 系列：PWM 提供多組獨立計數器；高達 15 路 ADC 並提供兩種模式：單次轉換與連續轉換模式。 #Product #Learning #Basic #zh-Hant - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/ms51-series-1t/ 聯絡我們： SalesSupport@nuvoton.com

經由ADC量測Bandgap電壓，能夠反推電池的電壓，再搭配電池的規格文件，可得知產品目前所剩電量。另外，結合新唐晶片內部紀錄bandgap電壓的機制，可以消除不同晶片間的製程誤差，以得到更精準的電池電壓量測結果。 - 更多產品資訊，請至新唐科技網站 https://bit.ly/3hVdcmC 購買管道：https://direct.nuvoton.com/tw/ 聯絡我們： SalesSupport@nuvoton.com

Nuvoton announced the latest ML51/ML54/ML56 microcontroller, built-in capacitive touch sensing, LCD driver highly integrated low power platform. Based on 1T 8051 core, running up to 24MHz, the power consumption in normal run mode is 80uA/MHz, lower than 1uA in power down mode the power consumption while power down with LCD on is lower than 20uA. - For more information, please visit Nuvoton Technology Website: https://bit.ly/3hVdcmC Buy now: https://direct.nuvoton.com/tw/low-power-8051-series/ Contact us: SalesSupport@nuvoton.com #Product #Learning #Basic #en