よくある質問
- M051 ベースシリーズ(95)
- M0518シリーズ(97)
- M0519シリーズ(43)
- M0564 シリーズ(1)
- ミニ 51 ベースシリーズ(90)
- ナノ 100/102 ベースシリーズ(101)
- Nano103 ベースシリーズ(10)
- ナノ 110/112 LCD シリーズ(100)
- ナノ 120 USB シリーズ(111)
- ナノ 130 アドバンストシリーズ(110)
- NUC029 シリーズ(94)
- NUC100/200 アドバンストシリーズ(102)
- NUC120/122/123/220 USB シリーズ(116)
- NUC121/125シリーズ(1)
- NUC126 USB シリーズ(2)
- NUC130/230 CAN シリーズ(103)
- NUC131/NUC1311 CAN シリーズ(98)
- NUC140/240 コネクティビティシリーズ(114)
- M451 ベースシリーズ(118)
- M451M シリーズ(117)
- M452 USB シリーズ(130)
- M4521 USB シリーズ(1)
- M453 CAN シリーズ(128)
- M463 CAN FD/USB HS シリーズ(1)
- M467 Ethernet/Crypto シリーズ(1)
- M471 シリーズ(1)
- M479 Motor Control Series(1)
- M481 Base シリーズ(4)
- M482 USB FS OTG シリーズ(4)
- M483 CAN シリーズ(4)
- M484 USB HS OTG シリーズ(4)
- M485 Crypto シリーズ(4)
- M487 Ethernet シリーズ(4)
- M4TK タッチキーシリーズ(25)
- NUC442/472 シリーズ(130)
- NUC472 Series(1)
- NUC505 シリーズ(138)
FAQ
What are ISP, ICP and IAP? Issue Date:2015-02-09
ISP stands for "In System Programming". The target chip runs the boot/loader code of LDROM through the peripheral interface such as USB/UART/SPI/I²C/RS-485/CAN... to update the internal APROM, Data Flash and User Configuration Word.
ICP stands for "In Circuit Programming". PC runs the software “NuMicro ICP Programming Tool” through the SWD (serial wire debug) port of Nu-Link circuit to update the internal APROM, LDROM, Data Flash and User Configuration Word of the target chip.
IAP stands for In-application-programming and it is a function for user to switch the code executing between APROM and LDROM without reset. User can enable the IAP function by re-booting chip and setting the chip boot selection bits in CBS (CONFIG0[7:6]) as 2 or 0. When chip boots with the IAP function enabled, any other page within the executable range of code can be mirrored to the first page of executable code (0x0000_0000~0x0000_01FF) any time. User can change the remap address of the first executing page by filling the target remap address to ISPADR and then go through ISP register with the Vector Page Re-map command. After changing the remap address, user can check if the change is successful by reading VECMAP(ISPSTA[20:9]).
(Below figure is the example for executable range of code with IAP Function Enabled of M05xDN/DE series.)
Products: | Microcontrollers ,Arm Cortex-M0 MCUs ,M051 Base Series ,M0518 Series ,Mini51 Base Series ,Nano100/102 Base Series ,Nano110/112 LCD Series ,Nano120 USB Series ,Nano130 Advanced Series ,NUC029 Series ,NUC100/200 Advanced Series ,NUC120/122/123/220 USB Series ,NUC130/230 CAN Series ,NUC131/NUC1311 CAN Series ,NUC140/240 Connectivity Series ,Arm Cortex-M4 MCUs ,M451 Base Series ,M451M Series ,M452 USB Series ,M453 CAN Series ,NUC442/472 Series ,NUC505 Series |
---|---|
Applications: | |
Function: | Peripherals,Memory,APROM,Config,Data Flash,Flash Memory Controller (FMC),LDROM,Software and Tools,Nu Tools,In Circuit Programming (ICP) Tool,In System Programming (ISP) Tool |