| I16-COB20 and I16-COB00
 I16COB20_UserManual.pdf
The I1600 COB's are used to demonstrate the voice quality and various durations of ISD1600B series. It can also be used as prototype boards for your initial applications.
There are two types of demo boards for ISD1600B series:
1) I16-COB20 : I1620B die is assembled.
2) I16-COB00 : Install the desired device into the PDIP socket. |
Actual Size = 3.8cm x 2.8cm
|
Product supported |
Ordering Code |
|
I1620B Die |
I16-COB20 |
|
I1610B/12B/16B/20B PDIP |
I16-COB00 |
Contents of Kit:
-
I16-COB20 / I16-COB00
-
User’s Manual
|
|
ISD-ES1600B_PROG
Single Socket Programmer
Users Manual
Installation Software
This board allows the programming of PCM audio files to the Nuvoton I1600B ChipCorder® IC controlled through the USB port of a PC. The record and playback functions of the chip may be selected in real time to demonstrate different sampling rates and playback quality of this chip for an end application. The PC connects to the demo board using a standard USB cable.
|
|
Actual Size = 6.1cm x 7.1cm
|
Products Supported |
Ordering Code |
|
ISD1610B/12B/16B/20B |
ISD-ES1600B_PROG |
Set-up Connections:
Before starting the ISD-ES1600B-Prog software application, make sure that the board is plugged into one of the PC’s USB ports and properly installed. Once the software starts, it will attempt to locate the board, but if no board is detected, an error message will be displayed. If so, it will be necessary to restart the software.
If detection of the board is successful, the main control panel will be displayed. The controls allow selection of the chip device, sample rate, volume decimation, and audio file to be recorded. However, the input audio file must be 8 kHz, 16-bit mono PCM.
System Requirements:
The demo board must be connected to a USB port on a PC running Windows 2000 or higher that supports Microsoft’s .NET framework v1.1 or higher.
Contents of Kit:
- ISD-ES1600B_PROG
- CD (User’s Manual and Installation Software)
|
ISD-COB 1700
COB/Demo Board for ISD1700 Series
The ISD-COB1700 is a COB/demo board for ISD1700 series. It has either a ISD1700 die or ISD1700 SOIC unit assembled to demonstrate the functionalities and voice quality of the ISD1700 device. The picture below illustrates all the input controls and output selections. The default settings for sampling frequency and output are 8kHz and PWM speaker outputs, respectively.
|
|
Actual Size = 5.4cm x 4cm
|
Products Supported |
Ordering Code |
|
ISD1730 |
ISD-COB 1700 |
|
ISD1740 |
|
ISD1750 |
|
ISD1760 |
|
ISD1790 |
|
ISD17120 |
|
ISD17150 |
|
ISD17180 |
|
ISD17210 |
|
ISD17240 |
-
ISD-COB1700
-
User’s Manual
|
|
|
ISD-ES17XX_USB_PB
Evaluation System for ISD1700 Series
ISD_ES17xxUSB_PB_UserGuide.pdf
S17xx Evaluation System Introduction
This demo system is for evaluation of all operations of the Nuvoton ISD17xx ChipCorder® IC controlled through the USB port of a PC in real time. The flexible and easy to use software coupled with the ISD7XX_USB-PB board makes a complete evaluation system for ISD17xx Series for an end application. The ISD17xx-USB-PB evaluation system also serves as Single Socket writer/ programmer.See batch programming section below.
The ISD7XX_USB-PB supports both modes of operations of ISD17xxx family.
- Push Button Mode( Battery Operated Stand-Alone)
- SPI Mode (USB controlled)
|
|
ISD17XX-USB-PB Board
DEVICE SUPPORTED:
|
Products Supported |
Ordering Code |
|
ISD1730 |
ES-17XX_USB_PB Rev E |
|
ISD1740 |
|
ISD1750 |
|
ISD1760 |
|
ISD1790 |
|
ISD17120 |
|
ISD17150 |
|
ISD17180 |
|
ISD17210 |
|
ISD17240 |
Chipcorder ® ISD- VPE1700 USB Demo Software Operation
The VPE1700 GUI interface consists of:
- Operational and board setting panels on top① ②
- Graphical Block diagrams of all possible input/output paths at the bottom screen. ③
Major Features:
- The GUI interface consists of two parts, a main operational panel and a configuration panel. Users will work on the operation panel most of the time while they will use configuration panels to setup the device before each operation.
- All GUI controls in this software are self-descriptive. Users can move the mouse cursor over the control button , a tools tip message will popup explaining the purpose of the current control; See above for example; placing mouse over record button will display Record ④
- A canvas window on the right side of the main panel, gives users insight of the current ISD17xx memory usage along with Rec/Play pointers and device ID. The blue bar shows empty rows in the chip. Once recorded, the corresponding rows will turn red. The yellow arrow indicates the play pointer and the red arrow indicates the record pointer. User can move the mouse cursor on these arrows to get the current play-pointer address or record-pointer address. After each operation, the pointers are updated in this canvas window.
- Once the board is attached and the device is powered up, any update on configuration settings will be effective immediately on the graphical block diagram automatically.
- This software supports all 17xx SPI commands.
- This Software supports batch programming. In Batch programming tab on configuration panel, users can add .wav files; program will calculate the rows needed for each file, assign addresses to these files and burn them into the chip.
CONTENTS OF KIT:
- One Sample ISD17130
- CD (with Applications Software and User’s guide with demo boards schematics)
- 8 Ohm Speaker
- USB Cable
Batch Programming
Batch programming allows users to preprogram multiple wav files into the chip by a single click. Users can select files, arrange file order , save into a project file, clear , load and burn these wav sounds to a continuous area of memory starting from row 16 (hex 10) of the memory a
|
|
|
ISD-ES1800
Demonstration Board for ISD1800 series
The ISD1800 Demo Board has been designed to allow a user to demonstrate the various features of the ISD1810 Devices. It also illustrates the simplicity of the operation of the devices.
The board is completely self-contained, including the batteries, a microphone, the switches and various passive components that make up a complete application. |
|
Actual Size = 8.3cm x 7.5cm
|
Products Supported |
Ordering Code |
|
ISD1806/10 |
ISD-ES1800 |
Contents of Kit:
- ISD-ES1800 Demo Board
- ISD1810 PDIP Sample
- 8-Ohm speaker.
- Instruction Sheet
- 3-AA Batteries
|
|
ISD-ES302
Demonstration Board for ISD4000 series
The ISD-ES302 Demo board is designed to let listeners hear the voice quality of the all ISD4000 product family and to demonstrate some of the features available through the SPI bus control. |
|
Actual Size = 12cm x 11.5cm
|
Products Supported |
Ordering Code |
|
ISD4002-120/150/180/240 |
ISD-ES302 |
|
ISD4003-04M/05M/06M/08M |
|
ISD4004-08M/10M/12M/16M |
Contents of Kit:
- ISD-ES302 Demo Board
- Three - ISD4003 PDIP Samples
- 16-Ohm Speaker
- 2-AA Batteries
|
|
ISD-ES501
Evaluation System for ISD5008
Users Manual
Installation Software
This evaluation system allows the complete operation of the ISD5008 controlled through the parallel port of a PC. All the functions of the chip may be selected in real time to allow complete evaluation of this chip for an end application.
|
|
Actual Size = 10cm x 8.5cm
|
Products Supported |
Ordering Code |
|
ISD5008 |
ISD-ES501 |
Set-up Connections:
The PC connects to the demo using a standard parallel cable from LPT1.
This board is designed to be used with software (Copyright 1999 National Instruments Corporation. All Rights Reserved) supplied by ISD. The software is supplied free of charge with the demo on A CD. The software paints a block diagram of the major components of the chip on the screen and the possible paths between them. When a path is selected, it lights up in yellow.
Systems Requirement:
- Window 2000 or later
- PC with Parallel Printer port
Contents of Kit:
- ISD-ES501 Evaluation board
- ISD5008 PDIP Sample
- CD (User's Manual and Installation Software)
|
|
|
|
ISD-ES502
Demonstration Board for ISD5008
Users Manual
Installation Software
The ISD-ES502 demonstration board illustrates the signal routing and flexibility of the ISD5008 as well as its recording and playback functions. The unit comprises an ISD5008, an ISD2560 to simulate background conversation, a Nuvoton W78E51 microcontroller, microphone and attendant circuitry, a seven-segment display for displaying mode and level information, and a keypad for selecting the modes. In addition, there are Power, Record, Pause and Play pushbuttons.
|
|
Actual Size = 20.3cm x 15cm
|
Products Supported |
Ordering Code |
|
ISD5008 |
ISD-ES502 |
Initial Setup
- When the ISD-ES502 board is initially received install the batteries, carefully observing polarity.
- If some of the LEDs light at this time, push the green Power Button to start unit properly.
-
Otherwise, push the green Power Button on the lower left to power on the unit. The ISD-ES502 will announce that it is "Ready" and conclude with the "-" in the middle of the numeric LED display turned on. Note that the unit will automatically turn itself off after a period of inactivity to conserve battery capacity. If one wants to shut it off earlier then just press the "*" button on the keypad. The ISD-ES502 will sound a tone and turn off.
- The ISD-ES502 is now ready for the user to choose the mode of operation.
Contents of Kit:
- ISD-ES502 Demo Board
- Two AA batteries
- Instruction Sheet
|
|
ISD-ES511
Evaluation System for ISD5100 series
This evaluation system allows the complete operation of the Nuvoton ISD5100 (ISD5102, ISD5104, chip may be selected in real time to allow complete evaluation of this chip for an end application. This ISD5108, ISD5116) ChipCorder IC controlled through the USB port of a PC. All the functions of the board supports both PDIP and TSOP packaged units for SOIC use a universal adapter to PDIP. The PC connects to the demo board using a standard USB cable. (Not included in the package) |
|
Actual Size = 9cm x 7.5cm
|
Products Supported |
Ordering Code |
|
ISD5116 |
ISD-ES511 |
|
ISD5108 |
|
ISD5104 |
|
ISD5102 |
Set-up
When the ISD-ES511 program is started, a search of the system is performed to locate the ISD-ES511 Board. The program then operates in one of two modes.
Operation without the ISD-ES511 Board:
The indicator in the upper left corner will indicate that a board was not found and its background color will be yellow. The command buttons and status indicator will not be functional, but the block diagram and configuration bits are functional. This will allow the user to quickly determine specific configuration words for use with the I51XX (I5102, I5104, I5108 or I5116). See below for operation of the block diagram.
Operation with the ISD-ES511 Board:
The indicator in the upper left corner will indicate that a board was found and its background color will be red. The red indicates that the socket on the ISD-ES511 board is powered off. The command buttons and status indicator will not be functional, but the block diagram and configuration bits are. After installing an ISD5100 (ISD5104, ISD5106, ISD5108, ISD5116) device, the socket can be powered up by selecting the Socket Power command button. Once the socket is powered up, the background color of the board indicator will turn to green. The command buttons are now enabled and device operation is allowed. See Device Operation below for details.
Systems Requirements:
The demo board must be connected to a USB port on a PC running Windows 98SE or later versions of the OS
Contents of Kit:
- ISD-ES501 Evaluation Board.
- CD (User’s Manual and Installation Software)
- 8-Ohm Speaker
|
|
ISD-ES512
Demonstration Board for ISD5100 series
Installation Software
This demo board allows the complete operation of the Nuvoton ISD5100 (ISD5102, ISD5104, chip may be selected in real time to allow complete evaluation of this chip for an end application. This ISD5108, ISD5116) ChipCorder IC controlled through the USB port of a PC. All the functions of the board supports both PDIP and TSOP packaged units for SOIC use a universal adapter to PDIP. The PC connects to the demo board using a standard USB cable. (Not included in the package) |
|
Actual Size = 8.7cm x 14.2cm
|
Products Supported |
Ordering Code |
|
ISD5116 |
ISD-ES512 |
|
ISD5108* |
|
ISD5104* |
|
ISD5102* |
*Requires SOIC to PDIP universal adaptor
Contents of Kit:
-
ISD- ES512 Demo Board
-
ISD5116 PDIP Sample
-
Instruction Sheet
-
Two AAA Baterries
|
|
ISD-ES521
Evaluation System for 5216
Users Manual
The ES521 evaluation system allows testing of all features of the chip and visually shows the signal flow through the chip. Writing to three 16-bit configuration registers sets up the signal flow. An active path is highlighted in blue while the gray arrows show possible but not currently active paths. |
|
Actual Size = 13.5cm x 11cm
|
Products Supported |
Ordering Code |
|
ISD5216 |
ISD-ES521 |
The top left corner of the application windows shows the configuration registers, they should look like in the following picture.
Application software at a glance:
Contents of the ISD-ES521 evaluation kit:
|